Memorise

Archive for the ‘Networking’ Category

Enabling advanced CLI on HP v1950 Switches

<HPE>xtd-cli-modeAll commands can be displayed and executed in extended CLI mode. Switch to extended CLI mode? [Y/N] :YPassword: foes-bent-pile-atom-shipWarning: Extended CLI mode is intended for developers to test the system. Before using commands in extended CLI mode, contact the Technical Support and make sure you know the potential impact on the device and the network.

Cannot send large messages via ActiveSync, iPhone/iPad

SYMPTOMS When sending from a Mobile device via the ActiveSync service the device fails to send. Some devices may return an error indicating that “The message that was sent to the server was rejected because the message was too large”. (Apple iPad iOS). Not all mobile devices behave this way and may just keep the message […]

Xerox Scan to email

C405 Set up scan to email  So onto the printer side. Open the webpage to configure the device (Enhanced web Service, shortened from here on as EWS) EWS > Connectivity > SMTP Which will show you this (normally I would pre-fill this with your settings, but since I don’t know your settings because of your SMTP […]

Office365 SMTP

Office 365 SMTP server settings Server: smtp.office365.com Alternative server: outlook.office365.com Port: 587 Encryption: TSL Authentication: Yes – use your full username and password. Note: Sending emails also works if TCP 25 is set as a port in connection settings, but using TCP 587 is recommended. Office 365 POP3 settings Server: outlook.office365.com Port: 995 Encryption: TSL Authentication: Yes – use your full username and password. Office 365 IMAP […]

Get All Users Outlook/Inbox Rules in Office 365

Get All Users Outlook/Inbox Rules in Office 365 Description:  PowerShell cmdlet to view inbox rules is Get-InboxRule. First grab all mailboxes in the organisation and store the UserPrincipalName in a variable.  Here we are storing it in a variable called “Users” Then for each user we are going to get the InboxRule and select several attributes: MailboxOwnerID Name Description […]

TEAM VIEWER Quick Support

https://download.teamviewer.com/download/TeamViewerQS.exe TeamViewer Quick Support PC https://download.teamviewer.com/download/TeamViewerQS.exe Team Viewer Quick Support MAC https://download.teamviewer.com/download/TeamViewerQS.dmg

How To Fix “Device eth0 does not seem to be present, delaying initialization” Error

check network: # ifconfig lo        Link encap:Local Loopback           inet addr:127.0.0.1  Mask:255.0.0.0           inet6 addr: ::1/128 Scope:Host           UP LOOPBACK RUNNING  MTU:16436  Metric:1           RX packets:0 errors:0 dropped:0 overruns:0 frame:0           TX packets:0 errors:0 dropped:0 overruns:0 carrier:0           collisions:0 txqueuelen:0           RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)  Try to start Eth0 device # […]

Debugging a Site to Site VPN on an Juniper SRX series

Within this article we will look at the various steps required in debugging a Site to Site VPN on an SRX series gateway. 1. CONFIRM CONFIGURATION First of all check the VPN configuration. This is also useful if and when you need to confirm the Phase 1 and Phase 2 parameter’s with the remote end. […]

CAN NOT ACCESS TO HTTPS MANAGEMENT OF JUNIPER SSG VI CHROME (ERROR CODE: ERR_SSL_VERSION_OR_CIPHER_MISMATCH)

Can not access to https management of Juniper SSG through Chrome (Error code: ERR_SSL_VERSION_OR_CIPHER_MISMATCH) A secure connection cannot be established because this site uses an unsupported protocol. Error code: ERR_SSL_VERSION_OR_CIPHER_MISMATCH Resolution 1: 1. Go to the “Chrome://flags” from the address bar. 2. Find “Minimum SSL/TLS” version support” 3. Select ” SSLv3″ option. Resolution 2: Access to WEB […]